Get Appoinment
Location » Home » Grades > Special Alloy > 5

AS 5 Enquiry | Print this page

5 Application:Australia Structural steel
Category Type Steel grade Standard Country
Grades Special Alloy 5 AS Australia

Chemical composition % of the ladle analysis of grade 5

C(％) Si(％) Mn(％) P(％) S(％)
0.35-0.45 0.10-0.40 0.50-1.00 0.04 0.040
5
Mechanical properties of grade 5
Proof strength
Rp0.2 (MPa)		 Tensile strength
Rm (MPa)		 Impact energy
KV (J)		 Elongation at fracture
A (%)		 Reduction in cross section on fracture
Z (%)		 As-Heat-Treated Condition Brinell hardness (HBW)
922 (≥) 475 (≥) 11 31 22 Solution and Aging, Annealing, Ausaging, Q+T,etc 122
Physical properties of grade 5
Property Density
kg/dm3		 Temperature T
°C/F		 Specific heat
J / kgK		 Thermal conductivity
W/mK		 Electric resistance
µΩ·cm		 Modulus of elasticity
kN/mm2		 Expansion rate
185 (≥) 548 (≥) 43 23 33 Solution and Aging, Annealing, Ausaging, Q+T,etc 321
Temp.
°C/°F		 Creep strain limit
(10000h)
(Rp1,0) N/mm2		 Creep rupture strength
(10000h)
(Rp1,0) N/mm2
245 824 359
5 Range of products
Product type Products Dimension Processes Deliver Status
Plates / Sheets Plates / Sheets 0.08-200mm(T)*W*L Forging, hot rolling and cold rolling Annealed, Solution and Aging, Q+T, ACID-WASHED, Shot Blasting
Steel Bar Round Bar, Flat Bar, Square Bar Φ8-1200mm*L Forging, hot rolling and cold rolling, Cast Black, Rough Turning, Shot Blasting,
Coil / Strip Steel Coil /Steel Strip 0.03-16.0x1200mm Cold-Rolled & Hot-Rolled Annealed, Solution and Aging, Q+T, ACID-WASHED, Shot Blasting
Pipes / Tubes Seamless Pipes/Tubes, Welded Pipes/Tubes OD:6-219mm x WT:0.5-20.0mm Hot extrusion, Cold Drawn, Welded Annealed, Solution and Aging, Q+T, ACID-WASHED
Cross Reference Table(Equivalent Grade)
Grade Standard Country Application
1Cr18Mn10Ni5Mo3N AS Australia
Of urea with good corrosion resistance, can produce urea corrosion of the equipment.
1Cr17Mn6Ni5N AS Australia
Nickel steel grade, instead of number 1 cr17ni7 and magnetism after cold working, used in railway vehicle, etc
1Cr18Mn8Ni5N AS Australia
Nickel steel, instead of 1cr18ni9
0Cr25Ni20 AS Australia
Oxidation resistance is better than 0cr23ni13. Mostly used as heat resistant steel
A-29 1025 AS Australia
General use carbon steel rod
1025 AS Australia
These products have been used typically for use in fabrication of fittings, but usage is not limited to such applications. These products are not typically used for deep forming or cupping operations.
G10250 AS Australia
General use carbon steel rod
G2500 AS Australia
Used in the products of the automobile, truck, tractor, and allied industries; small cylinder blocks, cylinder heads, air cooled cylinders, pistons, clutch plates, oil pump bodies, transmission cases, gear boxes, clutch housings, and light-duty brake drum
F10005 AS Australia
Used in the products of the automobile, truck, tractor, and allied industries; small cylinder blocks, cylinder heads, air cooled cylinders, pistons, clutch plates, oil pump bodies, transmission cases, gear boxes, clutch housings, and light-duty brake drum
G2500a AS Australia
Used in the products of the automobile, truck, tractor, and allied industries
G3500 AS Australia
Used in the products of the automobile, truck, tractor, and allied industries
G3500b AS Australia
Diesel engine cylinder block, truck and tractor cylinder block and cylinder head, flywheel, tractor transmission case and heavy-load gear box
G3500c AS Australia
Used in the products of the automobile, truck, tractor, and allied industries
W5 AS Australia
Carbon tool steel
T72305 AS Australia
Carbon tool steel
A5 AS Australia
Alloy tool steel
00Cr17Ni14Mo2 AS Australia
Austenitic stainless steel. Grade 00Cr17Ni14Mo2 was replaced by new designation 022Cr17Ni12Mo2 according to GB/T 20878 (2007)
X2CrNiMo18-14-3 AS Australia
Austenitic stainless steel. Grade 00Cr17Ni14Mo2 was replaced by new designation 022Cr17Ni12Mo2 according to GB/T 20878 (2007)
1.4435 AS Australia
Austenitic stainless steel. Grade 00Cr17Ni14Mo2 was replaced by new designation 022Cr17Ni12Mo2 according to GB/T 20878 (2007)
Z 3 CND 17-11-02 AS Australia
Austenitic stainless steel. Grade 00Cr17Ni14Mo2 was replaced by new designation 022Cr17Ni12Mo2 according to GB/T 20878 (2007)

Relevant products

5 Equivalent Grade Stock

Steel grade Dimension Shape Unit Quantity Delivery state Query
Cr12MoV 12-160(T)*310-610(W)*L Plate or Sheet Tons 12.38 Hot-Rolled+Annealed+black Enquiry
1.2601 12-160(T)*310-610(W)*L Plate or Sheet Tons 11.22 Hot-Rolled+Annealed+black Enquiry
A387 F5 & Grade 5 sheet Coil strip 0.5mmx200mmxC Coil or Strip Tons 3 Cold-Rolled+Annealed Enquiry
A387 F5 & Grade 5 Hot Coil stock Select Tons 3 Hot-Rolled+Annealed+black Enquiry
T45Cr5Si3 Round Bar Dia.40mm Round Bar Kgs 500 Hot-Rolled+Annealed+black Enquiry
1.2344(H13/X40CrMoV5-1/Z40CDV5) Stock List Dia.182mm - Dia.510mm Round Bar Tons 120 Forged+Annealed+black Enquiry
1.2714 Hot-Work Mould Steel Flat Bar Stock(2019-09-03) Select 0 Select Enquiry
15-5PH Forgrd Flat Bar Select 0 Select Enquiry
1.2714 Stock list 2020-06-15 Select 0 Select Enquiry
1.2714 QT Bar Stock List 2020-06-15 Select 0 Select Enquiry

Enquiry