EN EN 50C rV4 Enquiry | Print this page
| Category | Type | Steel grade | Standard | Country |
|---|---|---|---|---|
| Grades | Special Alloy | EN 50C rV4 | EN | Euronorm |
Chemical composition % of the ladle analysis of grade EN 50C rV4
| C(％) | Si(％) | Mn(％) | P(％) | S(％) | Cr(％) | V(%) |
|---|---|---|---|---|---|---|
| 0.48-0.55 | 0.15-0.40 | 0.70-1.00 | 0.035 | 0.035 | 0.90- 1.S0 | 0.10-0.20 |
| Proof strength Rp0.2 (MPa) |
Tensile strength Rm (MPa) |
Impact energy KV (J) |
Elongation at fracture A (%) |
Reduction in cross section on fracture Z (%) |
As-Heat-Treated Condition | Brinell hardness (HBW) |
|---|---|---|---|---|---|---|
| 256 (≥) | 873 (≥) | 11 | 24 | 33 | Solution and Aging, Annealing, Ausaging, Q+T,etc | 234 |
| Property | Density kg/dm3 |
Temperature T °C/F |
Specific heat J / kgK |
Thermal conductivity W/mK |
Electric resistance µΩ·cm |
Modulus of elasticity kN/mm2 |
Expansion rate |
|---|---|---|---|---|---|---|---|
| 614 (≥) | 219 (≥) | 22 | 42 | 24 | Solution and Aging, Annealing, Ausaging, Q+T,etc | 414 | |
| Temp. °C/°F |
Creep strain limit (10000h) (Rp1,0) N/mm2 |
Creep rupture strength (10000h) (Rp1,0) N/mm2 |
|||||
| 714 | 833 | 932 |
| Product type | Products | Dimension | Processes | Deliver Status |
|---|---|---|---|---|
| Plates / Sheets | Plates / Sheets | 0.08-200mm(T)*W*L | Forging, hot rolling and cold rolling | Annealed, Solution and Aging, Q+T, ACID-WASHED, Shot Blasting |
| Steel Bar | Round Bar, Flat Bar, Square Bar | Φ8-1200mm*L | Forging, hot rolling and cold rolling, Cast | Black, Rough Turning, Shot Blasting, |
| Coil / Strip | Steel Coil /Steel Strip | 0.03-16.0x1200mm | Cold-Rolled & Hot-Rolled | Annealed, Solution and Aging, Q+T, ACID-WASHED, Shot Blasting |
| Pipes / Tubes | Seamless Pipes/Tubes, Welded Pipes/Tubes | OD:6-219mm x WT:0.5-20.0mm | Hot extrusion, Cold Drawn, Welded | Annealed, Solution and Aging, Q+T, ACID-WASHED |
| Grade | Standard | Country | Application |
|---|---|---|---|
| X50CrMoV15 | EN | Euronorm | Steel rod, bars and steel wire for cold heading and cold extrusion - Part 5: Technical delivery conditions for stainless steels |
| 1.4116 | EN | Euronorm | Steel rod, bars and steel wire for cold heading and cold extrusion - Part 5: Technical delivery conditions for stainless steels |
| X50CrMoV15 | EN | Euronorm | Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes |
| 1.4116 | EN | Euronorm | Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes |
| X50CrMoV15 | EN | Euronorm | Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes |
| 1.4116 | EN | Euronorm | Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes |
| Z50C15 | EN | Euronorm | Stainless steels for general purposes. Plates, wide strips and strips |
| Z50CD15 | EN | Euronorm | Stainless steels for general purposes. Plates, wide strips and strips |
| Z50CD15CI | EN | Euronorm | Iron and steel. Cutlery stainless steel |
| Z50CMNNb21-09-02Az | EN | Euronorm | Valve steels and alloys for internal combustion engines |
| X50CrMnNiNbN21-9 | EN | Euronorm | Valve steels and alloys for internal combustion engines |
| 1.4882 | EN | Euronorm | Valve steels and alloys for internal combustion engines |
| Fe-Ni50Cr1 | EN | Euronorm | Nickel and nickel alloys. Iron-nickel alloys with particular dilatability |
| X45Cr13 | EN | Euronorm | Corrosion-resistant high-temperature steel |
| 1.3541 | EN | Euronorm | Corrosion-resistant high-temperature steel |
| X50CrSi8-2 | EN | Euronorm | Heat-treatable steels, alloy steels and free-cutting steels -- Part 15: Valve steels for internal combustion engines |
| X50CrMnNiNbN21-9 | EN | Euronorm | Heat-treatable steels, alloy steels and free-cutting steels -- Part 15: Valve steels for internal combustion engines |
| X50CrMoW9-1-1 | EN | Euronorm | Alloyed CrMoW steel |
| 50Cr50NiCb/50Cr50NiNb | EN | Euronorm | Standard Specification for Castings, Chromium-Nickel Alloy |
| ASTM 50Cr-50Ni-Nb | EN | Euronorm | Standard Specification for Castings, Chromium-Nickel Alloy |
