UNE X160CrMoV12 Enquiry | Print this page
| Category | Type | Steel grade | Standard | Country |
|---|---|---|---|---|
| Grades | Special Alloy | X160CrMoV12 | UNE | Spain |
Chemical composition % of the ladle analysis of grade X160CrMoV12
| C(％) | Si(％) | Mn(％) | P(％) | S(％) | Cr(％) | Mo(％) | V(%) |
|---|---|---|---|---|---|---|---|
| 1.45-1.75 | 1.15-0.45 | 0.20-0.60 | 0.030 | 0.020 | 11.0-13.0 | 0.70-1.00 | 0.70-1.00 |
| Proof strength Rp0.2 (MPa) |
Tensile strength Rm (MPa) |
Impact energy KV (J) |
Elongation at fracture A (%) |
Reduction in cross section on fracture Z (%) |
As-Heat-Treated Condition | Brinell hardness (HBW) |
|---|---|---|---|---|---|---|
| 947 (≥) | 213 (≥) | 14 | 33 | 41 | Solution and Aging, Annealing, Ausaging, Q+T,etc | 134 |
| Property | Density kg/dm3 |
Temperature T °C/F |
Specific heat J / kgK |
Thermal conductivity W/mK |
Electric resistance µΩ·cm |
Modulus of elasticity kN/mm2 |
Expansion rate |
|---|---|---|---|---|---|---|---|
| 617 (≥) | 438 (≥) | 33 | 13 | 34 | Solution and Aging, Annealing, Ausaging, Q+T,etc | 442 | |
| Temp. °C/°F |
Creep strain limit (10000h) (Rp1,0) N/mm2 |
Creep rupture strength (10000h) (Rp1,0) N/mm2 |
|||||
| 381 | 662 | 271 |
| Product type | Products | Dimension | Processes | Deliver Status |
|---|---|---|---|---|
| Plates / Sheets | Plates / Sheets | 0.08-200mm(T)*W*L | Forging, hot rolling and cold rolling | Annealed, Solution and Aging, Q+T, ACID-WASHED, Shot Blasting |
| Steel Bar | Round Bar, Flat Bar, Square Bar | Φ8-1200mm*L | Forging, hot rolling and cold rolling, Cast | Black, Rough Turning, Shot Blasting, |
| Coil / Strip | Steel Coil /Steel Strip | 0.03-16.0x1200mm | Cold-Rolled & Hot-Rolled | Annealed, Solution and Aging, Q+T, ACID-WASHED, Shot Blasting |
| Pipes / Tubes | Seamless Pipes/Tubes, Welded Pipes/Tubes | OD:6-219mm x WT:0.5-20.0mm | Hot extrusion, Cold Drawn, Welded | Annealed, Solution and Aging, Q+T, ACID-WASHED |
| Grade | Standard | Country | Application |
|---|---|---|---|
| D3 | UNE | Spain | Cold-Work Tool Steel |
| X165CrMoV12 | UNE | Spain | High alloyed CrMoV steel for cutting tool and cold work tool steel |
| 1.2601 | UNE | Spain | High alloyed CrMoV steel for cutting tool and cold work tool steel |
| SKD-11 | UNE | Spain | Mainly used for cold working mold: gauge, die for thread rolling, cutting tool for metal, forming roll, die for press. |
| SS 2310 | UNE | Spain | Cold work die steel, steel hardenability, quenching tempering hardness, wear resistance, strength are higher than the Cr12.Shape is complex, |
| X12M | UNE | Spain | Cold work die steel, steel hardenability, quenching tempering hardness, wear resistance, strength are higher than the Cr12.Shape is complex, |
| X160CrMoV12 / Z160CDV12 | UNE | Spain | Cold working alloy tool steels |
