ASTM D3 Enquiry | Print this page
| Category | Type | Steel grade | Standard | Country |
|---|---|---|---|---|
| Grades | Special Alloy | D3 | ASTM | USA |
Chemical composition % of the ladle analysis of grade D3
| C(％) | Si(％) | Mn(％) | P(％) | S(％) | Cr(％) | V(%) | W(%) |
|---|---|---|---|---|---|---|---|
| 2.00～2.35 | 0.10～0.60 | 0.20～0.60 | ≤0.030 | ≤0.030 | 11.0～13.5 | ≤1.00 | ≤1.00 |
| Proof strength Rp0.2 (MPa) |
Tensile strength Rm (MPa) |
Impact energy KV (J) |
Elongation at fracture A (%) |
Reduction in cross section on fracture Z (%) |
As-Heat-Treated Condition | Brinell hardness (HBW) |
|---|---|---|---|---|---|---|
| 575 (≥) | 565 (≥) | 14 | 43 | 13 | Solution and Aging, Annealing, Ausaging, Q+T,etc | 423 |
| Property | Density kg/dm3 |
Temperature T °C/F |
Specific heat J / kgK |
Thermal conductivity W/mK |
Electric resistance µΩ·cm |
Modulus of elasticity kN/mm2 |
Expansion rate |
|---|---|---|---|---|---|---|---|
| 521 (≥) | 314 (≥) | 13 | 23 | 11 | Solution and Aging, Annealing, Ausaging, Q+T,etc | 332 | |
| Temp. °C/°F |
Creep strain limit (10000h) (Rp1,0) N/mm2 |
Creep rupture strength (10000h) (Rp1,0) N/mm2 |
|||||
| 762 | 172 | 996 |
| Product type | Products | Dimension | Processes | Deliver Status |
|---|---|---|---|---|
| Plates / Sheets | Plates / Sheets | 0.08-200mm(T)*W*L | Forging, hot rolling and cold rolling | Annealed, Solution and Aging, Q+T, ACID-WASHED, Shot Blasting |
| Steel Bar | Round Bar, Flat Bar, Square Bar | Φ8-1200mm*L | Forging, hot rolling and cold rolling, Cast | Black, Rough Turning, Shot Blasting, |
| Coil / Strip | Steel Coil /Steel Strip | 0.03-16.0x1200mm | Cold-Rolled & Hot-Rolled | Annealed, Solution and Aging, Q+T, ACID-WASHED, Shot Blasting |
| Pipes / Tubes | Seamless Pipes/Tubes, Welded Pipes/Tubes | OD:6-219mm x WT:0.5-20.0mm | Hot extrusion, Cold Drawn, Welded | Annealed, Solution and Aging, Q+T, ACID-WASHED |
| Grade | Standard | Country | Application |
|---|---|---|---|
| D3 | ASTM | USA | Cold-Work Tool Steel |
| X165CrMoV12 | ASTM | USA | High alloyed CrMoV steel for cutting tool and cold work tool steel |
| 1.2601 | ASTM | USA | High alloyed CrMoV steel for cutting tool and cold work tool steel |
| SKD-11 | ASTM | USA | Mainly used for cold working mold: gauge, die for thread rolling, cutting tool for metal, forming roll, die for press. |
| SS 2310 | ASTM | USA | Cold work die steel, steel hardenability, quenching tempering hardness, wear resistance, strength are higher than the Cr12.Shape is complex, |
| X12M | ASTM | USA | Cold work die steel, steel hardenability, quenching tempering hardness, wear resistance, strength are higher than the Cr12.Shape is complex, |
| X160CrMoV12 / Z160CDV12 | ASTM | USA | Cold working alloy tool steels |
| Cr12 | ASTM | USA | Often used in the manufacture of small bear impact load and wear resistance of high cold cold punching die, punch, shear knife, cold roll, drill sets and wire drawing die, as well as the gauge, model, the CAM pin, eccentric wheel, etc |
| DNVGL VL GL D36 | ASTM | USA | High Strength Structural Steel Plate |
| DNVGL VL NV D36 | ASTM | USA | High Strength Structural Steel Plate |
Relevant products
D3 Equivalent Grade Stock
| Steel grade | Dimension | Shape | Unit | Quantity | Delivery state | Query |
|---|---|---|---|---|---|---|
| Cr12MoV | 12-160(T)*310-610(W)*L | Plate or Sheet | Tons | 12.38 | Hot-Rolled+Annealed+black | Enquiry |
| 1.2601 | 12-160(T)*310-610(W)*L | Plate or Sheet | Tons | 11.22 | Hot-Rolled+Annealed+black | Enquiry |