EN EN G17NiCrMo1.V6 Enquiry | Print this page
| Category | Type | Steel grade | Standard | Country |
|---|---|---|---|---|
| Grades | Special Alloy | EN G17NiCrMo1.V6 | EN | Euronorm |
Chemical composition % of the ladle analysis of grade EN G17NiCrMo1.V6
| C(％) | Si(％) | Mn(％) | P(％) | S(％) | Cr(％) | Ni(％) | Mo(％) |
|---|---|---|---|---|---|---|---|
| 0.15-0.19 | 0.50 | 0.55-0.80 | 0.015 | 0.015 | 1.30-1.80 | 3.00-3.50 | 0.45-0.60 |
| Proof strength Rp0.2 (MPa) |
Tensile strength Rm (MPa) |
Impact energy KV (J) |
Elongation at fracture A (%) |
Reduction in cross section on fracture Z (%) |
As-Heat-Treated Condition | Brinell hardness (HBW) |
|---|---|---|---|---|---|---|
| 496 (≥) | 527 (≥) | 32 | 31 | 41 | Solution and Aging, Annealing, Ausaging, Q+T,etc | 123 |
| Property | Density kg/dm3 |
Temperature T °C/F |
Specific heat J / kgK |
Thermal conductivity W/mK |
Electric resistance µΩ·cm |
Modulus of elasticity kN/mm2 |
Expansion rate |
|---|---|---|---|---|---|---|---|
| 747 (≥) | 299 (≥) | 33 | 43 | 31 | Solution and Aging, Annealing, Ausaging, Q+T,etc | 223 | |
| Temp. °C/°F |
Creep strain limit (10000h) (Rp1,0) N/mm2 |
Creep rupture strength (10000h) (Rp1,0) N/mm2 |
|||||
| 845 | 219 | 847 |
| Product type | Products | Dimension | Processes | Deliver Status |
|---|---|---|---|---|
| Plates / Sheets | Plates / Sheets | 0.08-200mm(T)*W*L | Forging, hot rolling and cold rolling | Annealed, Solution and Aging, Q+T, ACID-WASHED, Shot Blasting |
| Steel Bar | Round Bar, Flat Bar, Square Bar | Φ8-1200mm*L | Forging, hot rolling and cold rolling, Cast | Black, Rough Turning, Shot Blasting, |
| Coil / Strip | Steel Coil /Steel Strip | 0.03-16.0x1200mm | Cold-Rolled & Hot-Rolled | Annealed, Solution and Aging, Q+T, ACID-WASHED, Shot Blasting |
| Pipes / Tubes | Seamless Pipes/Tubes, Welded Pipes/Tubes | OD:6-219mm x WT:0.5-20.0mm | Hot extrusion, Cold Drawn, Welded | Annealed, Solution and Aging, Q+T, ACID-WASHED |
| Grade | Standard | Country | Application |
|---|---|---|---|
| NV6(5150) | EN | Euronorm | Steel for intake valves |
| HNV6 | EN | Euronorm | Steel for intake valves |
| S65006 | EN | Euronorm | Steel for intake valves |
| EV6 | EN | Euronorm | Steel for exhaust valves |
| S63015 | EN | Euronorm | Steel for exhaust valves |
| HEV6 | EN | Euronorm | Steel for exhaust valves |
| N07090 | EN | Euronorm | Steel for exhaust valves |
| 38CrSiV6 | EN | Euronorm | Alloyed CrSiV steel |
| 45SiCrV6 | EN | Euronorm | Alloyed CrSiV steel |
| 27CrMoV6-12 | EN | Euronorm | Alloyed CrMoV steel |
| 54NiCrMoV6 | EN | Euronorm | Alloyed NiCrMoV steel |
| 55NiCrMoV6 | EN | Euronorm | Low alloyed NiCrMo steel |
| 1.7715 | EN | Euronorm | Alloy special steel |
| 14MoV6-3 | EN | Euronorm | Alloy special steel |
| 15CDV6 Air 9160/C | EN | Euronorm | wrought steels used in aeronautical constructions |